Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Roofing: The Los Angeles Owner’s Guide
We stock and install Mr-Glass-compatible roofing parts across Los Angeles, with most replacements running $470 to $2,125 installed depending on the component and extent of the damage. Same-week scheduling is standard for parts we keep on the truck, and we’ll give you a written price before any work starts. Most Los Angeles homeowners discover a Mr-Glass part has failed the same way: a water stain appears on the ceiling after the first real rain of the season, or a skylight starts fogging between the panes and won’t clear.
Mr-Glass is known for glass-heavy roof assemblies: skylights, glass roof panels, and glazed sections that tie into conventional shingle or tile roofing. The failure is rarely the glass itself. It’s the flashing, the gasket, or the sealant around the glass losing its bond after years of Southern California sun exposure. UV breaks down the flexible seals faster than the glass ever degrades, and that’s where water gets in.
We’re an independent service provider, not affiliated with Mr-Glass. That means we can match original-equipment parts or install proven aftermarket equivalents without being locked into one distributor’s price or lead time. Curtis Lane, our owner, learned early that honesty about what a part actually costs is faster than making a homeowner wait two weeks for a mystery bid.
Which Mr-Glass Models This Applies To
Mr-Glass roofing products typically fall into three series families, and the compatibility issue is real: a gasket cut for a Series 3 skylight will not seat properly on a Series 4 frame, even if both are the same “nominal size.” The dimensional differences are small, usually 4 to 7 millimeters in the glazing channel, but that’s enough to leak within a year.
To identify your Mr-Glass unit, look for the stamped label on the aluminum frame edge or etched into the glass corner. You’re looking for a series code, a manufactured date, and a size designation in inches or millimeters. If the label is gone or sun-baked off, measure the visible glass opening width and height to the nearest 1/8 inch and photograph the glazing channel profile. That channel shape is how we match the right gasket or seal.
OEM Mr-Glass parts are available through authorized distributors, but lead times to Los Angeles often run two to four weeks and pricing runs 20 to 40 percent above equivalent aftermarket seals and flashings. When we install aftermarket, we use extruded aluminum and silicone or EPDM components that meet or exceed the original dimensional spec. We’ll tell you which makes sense for your situation and put that choice, with prices, in writing.
Styles & brands we work with
Signs Your Mr-Glass Roofing Is Failing
- Fogged or clouded glazing. A broken edge seal has allowed moisture into the airspace between glass panes. The glass is fine; the seal is done. This is the most common Mr-Glass failure we see in Los Angeles, and it means replacement of the insulated glass unit, not the whole skylight.
- Water stains on the ceiling or wall below. Flashing or sealant around the roof penetration has failed. It may be a slow drip that only shows during heavy rain. By the time the stain shows, water has been working into the substrate for weeks.
- Visible cracks in the glazing or frame. Curb-mounted units on flat Los Angeles roofs catch strong heat and thermal movement. A crack that starts hairline can open up with the next temperature swing.
- Discolored or lifted sealant beads. The original sealant has lost adhesion to the aluminum or the roof membrane. If you can pick at it with a fingernail and it lifts, it’s past time for replacement.
- Drafts or temperature swings near the unit. The gasket around the operable vent or movable panel has compressed and lost its recovery. You feel air movement around the frame even with the vent closed.
One note specific to Los Angeles: our dry-season rains followed by long heat stretches are hard on roof sealants. The wet-dry-wet cycle causes expansion and contraction that accelerates the failure of everything flexible under Mr-Glass frames.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Mr-Glass roofing work in Los Angeles, here’s what we price:
| Work Item | Installed Price Range, Los Angeles |
|---|---|
| Tile Roof Repair (Mr-Glass flashing/re-seal) | $710 – $2,950 |
| Roof Repair (sealant/gasket replacement around glass) | $470 – $2,125 |
The range is driven by access and condition. A single-story roof with a ladder-reachable curb takes less labor than a third-story glass section requiring hoist work. If the surrounding substrate has rotted from long-term water intrusion, that repair is outside the flashing or seal quote and we’ll document it with photos before proceeding. Every quote includes parts, labor, cleaning up the work area, and a written warranty through the 365-Day Done Right Promise. You’ll have a signed guarantee in hand before we leave, not emailed three days later.
DIY or Call Us?
A homeowner can safely inspect the visible sealant and look for cracked frames or fogged glass from inside. That’s worth doing. But replacing Mr-Glass glazing, gaskets, or flashing on a roof is work we don’t recommend doing yourself. The glass units are heavy, the roof edge is unforgiving, and the waterproofing sequence has to be right or you’re redoing it in six months. A wrong gasket depth or a misapplied sealant bead means the repair fails at the next rain, and you’ve spent a weekend and a few hundred dollars to learn that.
For anything involving removed glass or work at height, call (903) 568-7222 and we’ll put a real number on it. The estimate is free, and it’s in writing before we start.
FAQs
How long do Mr-Glass roof seals last in Los Angeles? In our Los Angeles climate, the flexible seals and gaskets around Mr-Glass units typically last 8 to 12 years before UV and thermal cycling degrade them, while the glass itself can last decades if the seal around it is maintained. If your unit is over ten years old, plan for a seal replacement even if it hasn’t leaked yet. Call (903) 568-7222 for a free estimate and we’ll let you know what shape yours are in.
Can the existing seal be repaired instead of replaced? A localized bead touch-up can extend a seal for a season or two if the rest of the run is still bonded, but once the sealant has lifted along more than a foot of the perimeter, it needs full removal and replacement to be waterproof. We’ll tell you if a repair is worth it or if you’re just pushing the replacement down the road. Call (903) 568-7222 and we’ll give you a straight number either way.
How long does a Mr-Glass gasket or seal replacement take? A standard single-unit gasket or seal replacement runs 3 to 5 hours on site, including old sealant removal, cleaning, and new material application with proper cure time. Larger glass sections or units needing reglazing can run a full day. When you call (903) 568-7222, we’ll give you a written schedule start-to-finish before you commit.
Do you stock Mr-Glass parts, or do I wait for them? We carry common Mr-Glass gasket profiles, sealants, and flashing kits on our trucks for the Los Angeles market, so many replacements happen same-week. Odd series or uncommon sizes may need a distributor order, and we tell you the lead time and price before anything is ordered. Call (903) 568-7222 with your model info and we’ll check stock while you’re on the phone.
Written by Curtis Lane, Owner, Bradford Remodeling at Bradford Remodeling, serving Los Angeles and nearby areas.
