Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Los Angeles Owner’s Guide
Boral fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on linear footage, post spacing, and whether we’re pulling an old fence or starting from a clean line. We stock Boral-compatible fence panels and posts on our trucks, and most straight-run replacements get done in a day. You probably landed here because a section of your Boral fence is leaning, a post cracked at the base, or a panel let go after the last Santa Ana wind event. We’ll walk through what you’re looking at, what it costs, and what “fixed” actually means.
Key Takeaways
- Installed Boral fence replacement in Los Angeles: $4,130 – $10,620, with the written price set before any work starts.
- Boral fencing is a composite product, not wood or vinyl – it fails differently, and parts selection matters.
- We’re an independent contractor, not affiliated with Boral. We install Boral and Boral-compatible systems.
- Every Boral fence installation we complete carries the 365-Day Done Right Promise in writing.
Which Boral Models This Applies To
Boral manufactures fence components under its TruExterior and Boral Fencing lines, with the post-and-panel system being the one we see most often in Los Angeles backyards. The critical compatibility gotcha is the post profile: Boral posts have a specific internal dimension and wall thickness. A standard 4×4 vinyl post sleeve will not seat a Boral panel properly. If you’re matching an existing Boral fence, measure the post cap width and the panel tongue profile before ordering anything. We’ve seen homeowners buy “close enough” aftermarket posts and end up with panels that rattle in the wind or crack at the tongue within a season.
OEM Boral parts carry the manufacturer’s weather-resistance spec, which matters in Los Angeles. Our sun exposure is not gentle on composites: inland neighborhoods like Woodland Hills and Sherman Oaks get sustained UV that fades and embrittles lower-grade polymer. We lean OEM for anything load-bearing (posts, gate frames) and will use quality aftermarket panels only when they match the OEM profile dimensionally. We carry common Boral post sizes, panel sections, post caps, and gate hardware on the truck. If your fence is a less common Boral line, we source the exact spec before we quote, not after.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
- Post lean at the base. Boral posts are set in concrete. When you see a post tilting, the concrete footing has usually cracked from soil movement, common in Los Angeles where expansive clay shrinks and swells with rain. Pulling and resetting is the fix, not shimming.
- Panel sagging between posts. If a panel dips in the middle, the internal aluminum stiffener has separated from the composite skin. This is a manufacturing wear point we’ve seen on older Boral runs, especially on runs longer than 6 feet between posts.
- Cracking at panel-to-post connection. The tongue where a panel slides into the post channel is the highest-stress point. High wind, especially the gusts through the Sepulveda Pass, flexes the panel and cracks the tongue over time.
- Discoloration or chalky surface. Boral composite will fade over years, but chalky residue that rubs off on your hand means the UV stabilizer in the outer layer is spent. The structural core is often fine, but the panel will keep degrading aesthetically.
- Gate dragging or sticking. A Boral gate that won’t close properly usually points to a post shifting, not a hinge problem. The gate frame is tied to the post, and when the post moves a half-inch, the whole gate goes out of square.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Los Angeles, a Boral fence installation runs from $4,130 on the low end for a short straight run with existing post holes in good shape, up to $10,620 for a longer run, gate installation, or a site that requires old fence demolition and concrete pour work. The biggest cost drivers are linear footage, post depth, and whether the ground is diggable with standard equipment. Some Los Angeles hillside properties have caliche or rock layers right where your post needs to go, and that adds time.
| Project Component | Typical Los Angeles Range |
|---|---|
| Short Boral fence run (under 40 linear ft) | $4,130 – $5,900 |
| Standard backyard replacement (40 – 80 linear ft) | $5,900 – $8,260 |
| Long run with gate and demo | $8,260 – $10,620 |
Every quote is a written, line-itemed price. You get the panel and post cost, labor, concrete, and disposal broken out. The number we give you is the number on the invoice. No change orders at the door, no “we found something” upcharges. Our work is covered by the 365-Day Done Right Promise: if the fence fails inside a year of install, Bradford comes back and makes it right at no charge. That’s in writing, every time.
DIY or Call Us?
What you can safely do: check your post bases for cracks, measure your panel width and post spacing to get a rough linear footage count, and note whether the failure is one panel or a structural post. That information lets us give you a tighter estimate over the phone. What you shouldn’t do: dig out and reset a leaning post yourself. A Boral post buried 24 to 30 inches in concrete is heavy, and the old footing has to come out completely or the new pour won’t hold. We’ve been called to fix dozens of homeowner reset attempts where the post was re-planted in the same cracked footing and failed again within months. Curtis Lane’s rule from too many Los Angeles job sites: get the footing right the first time, or you’ll be out there again next year. Call (903) 568-7222 for a straight quote.
FAQs
A properly installed Boral fence with OEM components typically lasts 20 to 25 years in Los Angeles, though UV exposure in inland areas like the San Fernando Valley will fade the surface sooner than coastal neighborhoods like Santa Monica. Post footings are what fail first here, not the panels. Call (903) 568-7222 if your footings are showing cracks.
Small surface cracks can sometimes be stabilized, but a tongue crack at the post connection or a separated internal stiffener means the panel is done – the repair won’t hold under wind load. Replacement is the honest call on structural panel damage. We’ll tell you which one you have when we look at it.
Most straight-run Boral fence replacements in Los Angeles take one day from demo to final post set. Runs with multiple gates, difficult digging, or retaining wall work can run two to three days. You’ll get a clear timeline in writing with your quote.
Yes. We carry common Boral post sizes, panel sections, post caps, and gate hardware on our trucks, along with parts for KraftMaid, Cambria, and Silestone lines. For less common Boral profiles, we source the exact OEM spec before we quote, so you’re never paying for a guess.
No. Bradford Remodeling operates under The Garrison Standard: written price before any work begins, and that’s the price you pay. The only exception is if you add scope, like deciding to extend the run once we’re on site. Any addition gets a new written line-item quote before we touch it.
Straight number, real scope, no surprises at the punch list. Call (903) 568-7222 to schedule your free Boral fence installation estimate in Los Angeles.
Written by Curtis Lane, Owner, Bradford Remodeling at Bradford Remodeling, serving Los Angeles and nearby areas.
