Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Los Angeles Homeowners Choose CGI Construction
Bradford Remodeling provides independent CGI repair in Los Angeles, focusing on CGI cabinetry, vanities, and finish work. We’re not authorized by CGI, and we don’t pretend to be. What we bring is years of hands-on experience with CGI’s Ready-to-Assemble and Semi-Custom lines, knowing exactly how their door profiles, box construction, and factory finishes hold up against Southern California’s dry heat, intense sun, and seismic movement. When a CGI Shaker door warps or a soft-close hinge gives out, we diagnose the cause, not just the symptom. Call (903) 568-7222 for a written estimate before any work starts.
CGI cabinets show up in a lot of Long Beach and Los Angeles kitchens and baths because they hit a decent price point for semi-custom looks. The trade-off is that the products demand proper installation and periodic hardware adjustment, especially in older homes where floors have settled and walls are no longer square. That’s the work we do. We level boxes, re-align faces, replace failed hardware, and match factory finishes so a repair doesn’t look like a patch job.
Why Trust Bradford Remodeling for Your CGI Construction?
Curtis Lane, our owner, grew up in the Crenshaw district watching his grandfather patch stucco and re-frame a back bedroom that never quite stayed square. That early lesson stuck: if the framing and substrate aren’t right, nothing you hang on them will be. Curtis trained in construction technology at Los Angeles Trade-Technical College on Washington Boulevard and spent nearly two decades doing everything from foundation work to finish carpentry across the Basin. These days, Bradford Remodeling is his operation, and the crew runs on a simple rule: straight number, real scope, no surprises at the punch list.
We work on CGI cabinetry and vanities the same way we work on KraftMaid, Cambria, Silestone, and Kohler installations. We read the manufacturer spec before we touch a box. We know which CGI door profiles are solid wood versus wrapped MDF, which drawer box joints are stapled rather than dovetailed, and which hinge plates need reinforcement on frameless cabinets. That’s the difference between a repair that lasts three years and one that fails when the Santa Anas dry the air out.
Every CGI service call starts with a written price. Not a verbal range, not a “we’ll see when we open it up.” A fixed number in writing, backed by the 365-Day Done Right Promise. If our CGI repair or installation fails within one year, we return and correct it at no charge. That guarantee is part of The Garrison Standard, the framework every Bradford Remodeling project operates under. It’s not a marketing line. It’s the document you hold in your hand when the job closes.
Styles & brands we work with
Common CGI Construction Problems We Fix in Los Angeles
Anaheim and Los Angeles create a specific set of stressors for CGI cabinetry. We see the same failures repeat across neighborhoods from Sherman Oaks to West Adams, and we’ve learned what causes each one. Here are the five most common CGI problems we address:
- Door warping and joint separation. CGI’s solid wood doors, especially in the Signature Series Shaker profiles, react to humidity swings. Los Angeles isn’t humid like Houston, but seasonal shifts between marine layer mornings and dry Santa Ana afternoons cause wood to expand and contract. Doors facing west windows or unshaded patio glass take the worst of it. We regularly see Shaker doors that have cupped or pulled away from their stiles. The fix is often door replacement matched to the existing finish, paired with re-seasoning the wood to the home’s actual humidity range before install.
- Drawer box stapling and glue failure. Many CGI Ready-to-Assemble cabinets use stapled drawer box joints with glue. Under daily load, especially in a kitchen with heavy pots and pans, those staples shear and the glue line cracks. The drawer starts sagging, then the face misaligns, then the slide binds. Replacing the box with a dovetailed or doweled aftermarket box, keeping the original CGI face, restores function without changing the kitchen’s look.
- Factory finish blistering and peeling. This is the failure we see most in Los Angeles homes with strong southern or western exposure. CGI’s factory finishes, especially on wrapped MDF doors and thermofoil surfaces, can blister or peel when they sit in direct sun or near a high-heat appliance like a double oven or a gas range with heavy use. The fix depends on the door’s substrate. Solid wood doors can often be re-coated; wrapped MDF doors usually need replacement. We’ll tell you which one applies to your kitchen before we quote.
- Soft-close hinge and slide wear. Dust is the silent killer of mechanical hardware in Los Angeles. Fine particulate from dry air, construction, and general city life works its way into Blum and similar soft-close mechanisms. Without periodic adjustment, the cylinders lose tension and the hinges start slamming or failing to close. Most homeowners don’t know these hinges have an adjustment screw. We service, adjust, and when needed replace the hardware, sometimes upgrading to a heavier-duty slide rated for more cycles.
- Box racking on settled floors. Older Los Angeles homes, particularly pier-and-beam foundations from the 1920s through 1950s, settle over time. When the floor dips, cabinet runs rack. Doors bind in corners. Face frames warp. We re-level the boxes, shim to true, and re-align the doors so the whole run sits square again. It’s not always a full reinstall; sometimes it’s a day of careful correction.
CGI Parts & Our Repair-vs-Replace Approach
When a CGI cabinet fails, our first question is whether the repair restores function and appearance for a reasonable cost. We don’t push full replacement when a targeted fix does the job. For doors and drawer fronts, we try to source OEM CGI panels first, especially for Signature Series profiles where the finish code needs to match. OEM matching keeps the kitchen uniform. When OEM isn’t available or a line has been discontinued, we source aftermarket doors and hardware that meet or exceed the original durability.
Hinges and slides are a different story. Many aftermarket manufacturers make components that outlast the original equipment, particularly in high-use kitchens. We stock a local inventory of soft-close hinges, full-extension slides, and drawer box hardware so we can turn around most CGI repairs within days, not weeks. The repair-versus-replace decision comes down to three things: the age of the cabinet line, the condition of the box structure, and whether the doors can be salvaged. We’ll show you the numbers on both paths and let you decide. Call (903) 568-7222 for an exact quote.
Our CGI Service Process – Step by Step
We run every CGI service call through the same four steps. No shortcuts, no surprises.
- 1
Diagnosis. We inspect the cabinets in place: box level, door alignment, hinge tension, drawer slide condition, and finish integrity. For warped doors, we measure moisture content with a meter. For racking, we check the floor with a level. The diagnosis produces a written scope of work with a flat-rate price. You sign it before we touch a tool.
- 2
Repair or installation. We execute the scope. If it’s door replacement, we order exact-match CGI panels or verified aftermarket equivalents. If it’s a full cabinet installation, we level every box, shim behind the face frames, and secure each run to the studs per manufacturer spec. For refacing, we remove old doors and hardware, prep the boxes, and install new fronts with adjusted hinges.
- 3
Testing and adjustment. Every door opens and closes at the correct tension. Every drawer slides on full extension without binding. Every soft-close mechanism engages. We cycle each door and drawer ten times minimum, then adjust anything that isn’t right.
- 4
Walkthrough and written warranty. You walk the job with the lead on site. We confirm the scope is complete, the site is clean, and you have the 365-Day Done Right Promise in your hand. If anything fails within a year, we return and correct it at no charge.
CGI Products We Service & Install in Los Angeles
We work across the main CGI product lines found in Los Angeles homes. That includes the Ready-to-Assemble (RTA) cabinet series, the Semi-Custom Wood cabinet line, Signature Series door profiles like Shaker and Raised Panel, and the Bath Vanity Collection. We stock a local parts inventory covering common hinge plates, soft-close slides, drawer box components, and finish-match materials for the most-requested CGI colors and wood species. If you’re not sure which line your cabinets came from, we can identify it during the diagnosis.
We also handle full kitchen and bath remodels where CGI is part of a larger scope. That means we install the cabinets, cut and set the countertops, trim the backsplash, and coordinate plumbing and electrical rough-in where the job calls for it. One crew, one scope, one written price.
See the difference
Before
After
Before
After
Before
AfterWe Also Service These Brands
CGI isn’t the only cabinet and finish line we work with. Bradford Remodeling installs and services KraftMaid, Cambria, Silestone, and Kohler products, among others. If your kitchen or bath has mixed brands, we handle the whole scope without pointing you to another contractor.
FAQs – CGI Construction Service in Los Angeles
Can you match the factory finish on my CGI cabinets if you only replace a few doors? Yes, in most cases we can match the factory finish by working with CGI’s finish codes and ordering exact-match panels from the same series. For discontinued colors, we work with a local finishing shop that color-matches and applies a compatible topcoat. If you’re replacing more than a few doors, sometimes a full refacing gets you a more uniform result for a similar cost. Call (903) 568-7222 and we’ll tell you what applies to your specific cabinet line.
My CGI cabinet doors are warping in the LA heat – can they be fixed, or do I need new cabinets? Warped doors usually need to be replaced, but the boxes underneath are often fine. The wood doors are the component reacting to heat and humidity; the cabinet boxes, if properly installed, hold their shape. We replace the affected doors with exact-match or upgraded panels, re-level the boxes, and adjust the hinges. Replacing the entire cabinet run is rarely necessary. Call (903) 568-7222 for a diagnostic visit and a fixed repair quote.
Do you use CGI original parts for hinges and drawer slides, or aftermarket? We use OEM CGI parts when they’re available and match the existing hardware spec. When OEM parts are backordered or discontinued, we source aftermarket hardware that meets or exceeds the original cycle ratings. For soft-close hinges and full-extension slides, we often recommend aftermarket upgrades that hold up better under heavy daily use. We’ll show you both options with prices before we order anything.
How do CGI cabinets hold up in bathrooms with high humidity, like a master bath with a steam shower? CGI bathroom vanities hold up reasonably well in normal bathroom conditions, but a steam shower changes the equation. The sustained humidity accelerates finish breakdown on wrapped MDF doors and can swell exposed edges. We recommend solid wood doors with a sealed finish for steam-adjacent vanities, and proper ventilation as the first line of defense. If your existing CGI vanity is failing in a high-humidity bath, we’ll evaluate whether refacing with moisture-resistant materials makes more sense than replacing with the same product.
Can you install CGI cabinets in a kitchen with an existing non-CGI layout, or do you only work with full CGI kitchens? We install and service CGI cabinets in any kitchen, whether it’s a full CGI run or a mixed-brand layout. What matters is the box dimensions, the door profile, and the hardware spec. We work around existing non-CGI cabinets, match heights and depths, and make the transition look intentional. No need to rip out cabinets that are still doing their job.
How much does CGI construction cost in Los Angeles? Cabinet installation on a CGI kitchen typically runs $4,720 to $15,340, depending on the cabinet count, door profiles, and hardware upgrades. A full kitchen remodel with CGI cabinets falls between $16,520 and $53,100. Bathroom remodels range from $10,620 to $33,040. Countertop installation adds $2,360 to $7,670, and backsplash work runs $945 to $2,950. These are fixed ranges, not open-ended estimates. Call (903) 568-7222 for a written quote on your specific scope.
CGI Service Pricing in Los Angeles
| Service | Price Range |
|---|---|
| Cabinet Installation | $4,720 – $15,340 |
| Kitchen Remodel | $16,520 – $53,100 |
| Bathroom Remodel | $10,620 – $33,040 |
| Countertop Installation | $2,360 – $7,670 |
| Backsplash Installation | $945 – $2,950 |
We recently refaced a 14-year-old CGI kitchen in a Glendale area home where the Shaker doors had warped and the finish was blistering from years of west-facing sun. Our crew replaced the damaged doors with exact-match CGI panels, upgraded to soft-close hinges, and re-leveled the boxes to account for seasonal movement. The homeowners avoided a full gut remodel. The kitchen is holding up two summers later.
Book Your CGI Service in Los Angeles, CA
If your CGI cabinets need repair, refacing, or full installation in Los Angeles, call (903) 568-7222. We’ll schedule a diagnostic visit, put a written price in front of you, and stand behind the work for a full year. No urgency tactics, no pressure. Just a straight number and a real scope.
Written by Curtis Lane, Owner at Bradford Remodeling, serving Los Angeles since 2004.
