Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Los Angeles Owner’s Guide
Jerith fence installation in Los Angeles typically runs $4,130 to $10,620 for a complete aluminum fence system on an average city lot, and we stock Jerith-compatible posts, panels, gates, and hardware locally. Most homeowners don’t call us until a gate droops, a post leans after a rain, or a panel pulls loose at the corner bracket – by then they’ve usually been living with a wobbly fence for months. We’re an independent contractor, not affiliated with Jerith Manufacturing, but we’ve been installing and repairing their aluminum residential fence lines long enough to know the part numbers by heart.
Key Takeaways
- Installed cost for a Jerith aluminum fence in Los Angeles: $4,130 – $10,620 for a typical 60 – 120 linear foot run, depending on grade, gate count, and post depth.
- Most common failure points: corner brackets, post caps, gate hinges, and the dry-set post anchors Jerith specifies for pool enclosures.
- Parts we carry: Jerith residential line posts, gate frames, latch bars, rail ends, and touch-up paint matched to Jerith’s textured bronze and white finishes.
- Time frame: a full replacement runs 2 – 3 days on site. Gate hardware swaps finish in an afternoon.
Which Jerith Models This Applies To
Jerith’s residential aluminum fence line breaks into three families we see constantly across Los Angeles yards: the Classic series (2-rail and 3-rail panels, flat-top or spear-top pickets), the Deerfield decorative series (taller panels with ring-top or fleur-de-lis finials), and the Sentry pool code line, which meets BOCA and IBC pool barrier codes. Each series uses its own rail punch pattern and bracket depth. A Classic post will take a Deerfield panel only if you shim the rail channel, which is a shortcut we won’t do – it voids the structural load path.
If you’re trying to match a part on your own, check the inside face of the post, just under the cap. Jerith stamps a date code and the post’s wall thickness there. Panels have the series name on a small aluminum tag near the bottom rail. For gate frames, measure the hinge pocket spacing: Sentry gates hinge at 24-inch centers. Classic and Deerfield gate frames swing on 22-inch centers. If you mix those, the gate will bind at the latch post, and no amount of hinge shimming fixes it. OEM parts run 30-40% higher than quality aftermarket equivalents from suppliers like SHI or Ultra Aluminum, and for most 2005-and-newer models the aftermarket match is dimensionally identical. If your fence is pre-2005, go OEM – Jerith changed their rail punch tooling slightly, and aftermarket rails won’t seat.
Styles & brands we work with
Signs Your Jerith Fence Installation Is Failing
- Gate drags on the latch side. The hinge posts have rotated slightly in their footing, or the hinge brackets have elongated at the screw holes. In Los Angeles’s shrink-swell clay, a gate post set less than 30 inches deep will move within two wet seasons.
- Corner panel pulls out of its bracket. The self-tapping screws Jerith uses in corner brackets are only stainless on the face; the shank can corrode inside the rail channel, especially in coastal neighborhoods like Playa del Rey or San Pedro where salt air works the aluminum’s oxide layer harder.
- Post cap pops off in the wind. This is almost always a retrofit issue – the cap’s retainer prongs got bent when the fence was originally assembled, or the post was cut slightly out of square and the cap never seated fully.
- Aluminum blooms at the post base. You’re seeing galvanic corrosion where the aluminum post reacts with the wet-set concrete. It’s cosmetic mostly, but it tells you water is ponding in the footing, which cycles the post base through daily expansion and contraction.
- Pool gate won’t self-close under code inspection. Jerith’s tension springs fatigue after about 8-10 years of daily use. The spring looks fine but loses its return force, and a three-inch gap at the latch fails the BOCA self-closing requirement for pool enclosures in the City of Los Angeles.
Replacement Cost & What’s Included
For a Jerith fence installation or full reinstallation in Los Angeles, our written quotes land between $4,130 and $10,620. That’s the complete installed range: panels, posts, gates, hardware, concrete footings, and clean-up. What moves the number is total linear feet, how many gates you have, whether we’re setting posts in soil (dig and wet-set) or existing concrete (core drill, epoxy-set), and whether your grade changes more than 6 inches across the run – that forces stepped panels and longer post lengths.
The breakdown is transparent: materials run 55-65% of the total, labor and footings the rest. We bring the parts, the concrete, the core drills, and the touch-up paint. A 60-foot run with one walk gate and one 10-foot double drive gate lands around $5,500-$6,800. A 120-foot pool enclosure with four pool-code gates and stepped grade can hit $10,500. Every job gets a written line-item bid before we break ground, and the work carries our 365-Day Done Right Promise – if a post shifts, a gate binds, or a bracket fails inside a year, we return and correct it at no charge.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Replacing a Jerith post cap or tightening a picket screw is a Saturday-morning job with a drill and a hex key; go ahead. What gets dangerous is lifting a full aluminum panel against a gust of Santa Ana wind – a 6-foot by 8-foot panel is a 40-pound sail that can catch you across the face or knock a ladder sideways. And post replacement, gate re-hanging, or anything involving concrete footings is in our lane. A leaning post is not a cosmetic issue: it’s a lever arm pulling the adjacent panels and brackets out of plane. If you’ve got a gate that drags, a post that leans, or panels that have started to twist, call us at (903) 568-7222. We’ll send a tech who knows Jerith’s rail geometry, measure the job, and put a written number in your hand within 48 hours.
FAQs
A properly set Jerith aluminum fence lasts 25-40 years in Los Angeles; the aluminum is factory-painted with a baked polyester powder coat that’s rated for a 20-year no-fade warranty by Jerith, and the structural failure we see is always in the footings and brackets, not the panels themselves. Salt air near the coast and sprinkler overspray against the post bases shorten that to 15-25 years without routine maintenance. Call (903) 568-7222 for a condition assessment on an older run.
Yes, in about 60% of cases we repair rather than replace – we re-set post footings, swap bent brackets, replace gate springs and hinge pins, and touch up powder coat where it’s cracked at stress points. However, if your posts are bent at the base from a vehicle strike or the panels are twisted beyond 10 degrees anywhere along the run, replacement of the affected section is cheaper than trying to pull aluminum back true. Call (903) 568-7222 and we’ll tell you straight which side of that line your fence sits on.
A standard 60-100 linear foot Jerith fence replacement in Los Angeles takes 2-3 days on site for a Bradford Remodeling crew: one day to remove and set posts, a second day to hang panels and gates, and a final day for punch list, latch adjustments, and a full site cleanup. The only thing that extends it is rain – wet concrete footing pours get pushed to the next dry day. We’ll give you the exact schedule in writing before any of it starts; call (903) 568-7222.
We keep Jerith-compatible residential posts, corner brackets, gate frames, latch bars, tension springs, post caps, and touch-up paint for the Classic, Deerfield, and Sentry lines on our service trucks throughout Los Angeles, so gate hardware and panel repairs usually finish same-visit. When we install, we work with the name-brand materials our crews spec – KraftMaid, Cambria, Silestone, and Jerith among them – so the parts are traceable and the manufacturer warranties stand. Call (903) 568-7222 and tell us what’s failing; we’ll confirm the part exists before we roll out.
Square Away Your Fence in Los Angeles
If your Jerith fence has been drooping at the latch or leaning through the last two winters, don’t let it go another season. Call Bradford Remodeling at (903) 568-7222 to schedule a free estimate. Curtis Lane will look at your posts, tell you what’s actually wrong, and price the fix in writing – straight number, real scope, no surprises at the punch list. That’s The Garrison Standard every Bradford project runs on, and it’s the same standard we’ve held since 2004.
Written by Curtis Lane, Owner, Bradford Remodeling at Bradford Remodeling, serving Los Angeles and nearby areas.
